How To Clean Condenser And Coils On A Trane A/c Unit

How to Make clean an Outdoor Air Conditioning Curl (Trane unit example)

September 13, 2022 | by Ethan (email) |

Twice in five years I've cleaned my outdoor Ac condenser, and both times I've been amazed past the amount of clay and  leaves I've found. Fortunately, cleaning your outdoor coil is a chore that whatsoever homeowner can reach, and it doesn't take very long. A good cleaning will aid your Air conditioning unit to office more than efficiently, and potentially brand it last longer too. Read on to learn how I removed the fan, outside panels and scrubbed away a lot of dirt and debris from my outdoor Air conditioning condenser.

Editors note: This mail service originally ran in August 2009. In a related postal service nigh AC maintenance, one reader asked well-nigh cleaning an outdoor condenser unit, which prompted united states to update this mail service with more pictures and information. If y'all find it helpful, give information technology a +1. Else, exit a comment and we'll try to go far meliorate.

Outdoor Condenser Coil

The coil transfers heat from your home to the outside, and this procedure works best when air can move freely. That's why outdoor units take those big 'ol fans. When dirt and leaves block up air passages, information technology's that much harder to cycle enough air. Plus, clay and even dust can settle on the AC fins making them much less efficient. This in turn raises operational costs and shortens the lifespan of your compressor.

How to Make clean your Air-conditioning Unit (Trane XE1200 as example)

This project doesn't require much in the way of tools. You'll need a nut driver to remove some metal screws, a hose, and a scrubber. I've got a handy castor that allows me to attach the hose and pump water through the bristles. Cleaning my condenser is pretty much the perfect application for it.

Cleaning the Unit
It's best to start by turning off the billow supplying power to the unit, and hopefully your panel is labeled better than mine. Side by side, remove any nearby obstructions. Most installation manuals will let you know the minimum clearance effectually and in a higher place the unit. If y'all don't have admission to the manual, try for at least 2 feet.

My unit of measurement has louvered sides held together with a lot of metal screws, and I'd judge I removed about xxx screws all together. Fortunately, they're all the aforementioned. But go along rails of where they all go. If your unit has a grill instead of louvers, don't even bother taking the sides off. You can effectively clean everything as is.

You'll see screws around the perimeter, at the corner where the top and sides meet (not the screws circling the fan). After y'all remove all those screws, the peak (and fan) tin be lifted off. Be careful because the fan is tethered with electrical wires. If the installers had whatever sense, they left a generous length of wire and you lot tin lean the top nearby.

This picture shows the electrical compartment.

And hither yous see the compressor.

The side grills have more screws at all the corners and forth the bottom edge. Afterward you remove these screws you'll see how the sides overlap and can be lifted upwardly and off. It'south a good idea to remember where each panel was located. They should be identical, only this'll help ensure that spiral pigsty line up when you put information technology back together.

Use your hose and brush to clean the grills, and hose down the fins (do not scrub the fins!). The fins maximize surface area for the oestrus exchange so if you accidentally mash them together, they won't work nearly besides. Even an invisible layer of dust decreases efficiency and so run your hose over everything (except the electric).

I think this was the beginnings of a nest.

You can see the fins and a few places where the fins are bent- probably from when the previous owner had the compressor replaced.

This shows some of the gunk I found on the fins.

And hither'south everything brilliant and make clean.

Tips for Cleaning Your AC Unit

• Some of the parts are heavy or awkward. A second pair of easily is a good idea.
• Compressed air can be useful to clean effectually electrical parts. Information technology's also a practiced alternative if you can't use a water hose.
• You can also spray your coil with a cleaning solution such as AC cleaner or soapy h2o.

What practice you lot recall? When was the final fourth dimension you cleaned your outdoor unit?

Source: https://www.oneprojectcloser.com/cleaning-you-outdoor-air-conditioning-coil-trane-unit-example/

Posted by: bauersming1945.blogspot.com

Share this post